. Menunjukkan proses routing yang sedang berjalan di router.
2. Timers yang sedang berjalan termasuk waktu update selanjutnya (10 detik).
3. Fungsi filetering untuk update yang akan diterima atau dikirimkan. Redistributing pada contoh diatas menunjukkan rip, sehingga router menggunaikan routing rip untuk menerima dan mengirim update.
4. Menunjukkan interface yang digunakan untuk mengirim dan menerima update rip, serta versi rip yang digunakan.
5. Automatic is in effect menunjukkan bahwa router tsb melakukan summarizing to the classful network boundary. Maximum path : 4 menunjukkan how many equal-cost router RIP will use to send traffic to the same destination.
6. Menunjukkan Classful network address dikonfigurasikan pada router rip.
7. Menunjukkan RIP neighbors dimana router menerima update, termasuk next-hop IP Address dan Administrative Distance. Untuk last update menunjukkan waktu update terakhir. Distance menunjukkan nilai AD = 120 -> RIP.
Perintah show ip protocols dapat digunakan untuk mem-verifikasi bahwa rute yang diterima RIP tetangga ada dalam table routing.
Output dari perintah show ip route dapat memberi informasi tentang penggunaan routing protokol RIP yang ditandai dengan “R”. Dibawah ini adalah code atau perintah Verifikasi RIP dengan Ip Show route dan perintah debug .
Dibawah ini adalah code nya :
R1#show ip route
Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP
D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP
i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area
* - candidate default, U - per-user static route, o - ODR
P - periodic downloaded static route
Gateway of last resort is not set
C 192.168.1.0/24 is directly connected, FastEthernet0/0
C 192.168.2.0/24 is directly connected, Serial0/0/0
R 192.168.3.0/24 [120/1] via 192.168.2.2, 00:00:04, Serial0/0/0
R 192.168.4.0/24 [120/1] via 192.168.2.2, 00:00:04, Serial0/0/0
R 192.168.5.0/24 [120/2] via 192.168.2.2, 00:00:04, Serial0/0/0
R1#
R2#show ip route
<Output omitted>
R 192.168.1.0/24 [120/1] via 192.168.2.1, 00:00:22, Serial0/0/0
C 192.168.2.0/24 is directly connected, Serial0/0/0
C 192.168.3.0/24 is directly connected, FastEthernet0/0
C 192.168.4.0/24 is directly connected, Serial0/0/1
R 192.168.5.0/24 [120/1] via 192.168.4.1, 00:00:23, Serial0/0/1
R2#
R3#show ip route
<Output omitted>
R 192.168.1.0/24 [120/2] via 192.168.4.2, 00:00:18, Serial0/0/1
R 192.168.2.0/24 [120/1] via 192.168.4.2, 00:00:18, Serial0/0/1
R 192.168.3.0/24 [120/1] via 192.168.4.2, 00:00:18, Serial0/0/1
C 192.168.4.0/24 is directly connected, Serial0/0/1
C 192.168.5.0/24 is directly connected, FastEthernet0/0
R3#
R1#debug ip rip
R1#RIP: received v1 update from 192.168.2.2 on Serial0/0/0
192.168.3.0 in 1 hops
192.168.4.0 in 1 hops
192.168.5.0 in 2 hops
RIP: sending v1 update to 255.255.255.255 via FastEthernet0/0 (192.168.1.1)
RIP: build update entries
network 192.168.2.0 metric 1
network 192.168.3.0 metric 2
network 192.168.4.0 metric 2
network 192.168.5.0 metric 3
RIP: sending v1 update to 255.255.255.255 via Serial0/0/0 (192.168.2.1)
RIP: build update entries
network 192.168.1.0 metric 1
This is dummy text. It is not meant to be read. Accordingly, it is difficult to figure out when to end it. But then, this is dummy text. It is not meant to be read. Period.
ConversionConversion EmoticonEmoticon